Central Hobbies

Orders Only: 1-800-723-5937           Information: 1-406-259-9004
Hours: Mon - Sat 10-6 MST

 
0 products in cart | Total: $0.00
 
 

Central Hobbies
1401 Central Avenue
Billings, MT 59102

We Gladly Accept:
Central Hobbies is secured by Comodo SSL
as well as
PayPal Verified Merchant

Part#: LUMENIERBUNDLE
Lumenier Quadcopter Bundle
Product Details:

 Lumenier Charpu Frame:

The QAV-X features a unique FPV camera and HD mounting system. The FPV camera is recessed partially below the top plate and protected by the top cross bar, guarding your electronics. At the same time, the camera side walls act as an angled wedge to set your HD camera on for recording, such as a GoPro, at a 35 degree angle. No need to 3D print custom mounts to angle up your camera anymore, just add some of the included neoprene foam, securely strap down your camera and fly!

Lumenier QAV-X CHARPU

The main "unibody" 3mm plate is CNC milled out of a solid sheet of premium Lumenier carbon fiber. The outer weave of the carbon fiber runs 100% down each arm of the QAV-X (0/90 weave), maximizing the strength of the carbon and arms. The center layers are offset at 45 degrees providing even and balanced strength throughout the entire plate.

The top plate includes an accessory antenna extension plate, allowing for multiple cable ties to lock down your antenna in place. No more damaging the SMA connection on your VTX. The top plate also has a cutout allowing access to your VTX button and LED displays for easy channel adjustment. The balancing bumps on the sides of the top plate make it easy to measure the center of gravity on your frame in the field to get the perfect balance.

Each kit includes a carbon fiber battery protector plate. The airframe is designed to strap a LiPo battery to the bottom, leaving the battery exposed during a hard landing or crash. Use this included plate to wrap underneath the battery, sandwiching the pack between the main plate and protector plate. Additionally, you can use the included Neoprene foam to create a landing pad on the bottom of the battery protector plate. This will help keep the airframe upright during take off and landings.

The airframe comes with high quality aluminum hardware. All screws are premium, black oxide steel. The spacers have a textured grip surface treatment, which facilitates holding of the spacers during assembly and servicing of the airframe. The spacers are also 28mm tall vs the standard 35mm. This gives the airframe a sleek, low profile look.

Included with the QAV-X CHARPU kit is the popular Lumenier 4Power power distribution board which can be fitted with an optional Pololu voltage drop-down circuit (to 12v or 5v), and a XT60 pig-tail. Like the QAV210/180, the QAV-X kit enables mounting of small FPV cameras such as the Lumenier CM-650 in a fully encased assembly which protects the FPV camera during crashes and enables pointing the FPV camera at a wide variety of viewing angles.
Features

    Full 3K Carbon Fiber airframe featuring a solid 3mm main plate.
    Dual purpose FPV and HD camera mounting solution.
    Compact size for 5" propellers, 214mm motor to motor.
    Black Oxide steel screws
    Easy grip black anodized spacers
    Multiple motor mounting holes to fit a variety of motors (M3 and M2 screw mounting patterns).
    "Bumpers" on the end of the arms to protect the motor during a crash, just like the QAV250.
    Included Lumenier 4Power power distribution board and XT-60 Pig-Tail to power ESCs and FPV flight electronics. The PDB can optionally be outfitted with a Pololu 12v or 5v voltage step-down (Pololu board not included).
    LiPo battery protection plate included.
    Designed around popular 26mm sized cams in cases such as the Lumenier CM-650 or HS1177.
    Support to carry HD camera at 35 degree angle(such as the GoPro 4, Xiaomi Yi, etc).
    Lightweight and rigid

Weight

    Airframe: 72g (airframe + hardware), 77g (with battery protector plate).

Versions

The QAV-X is designed to fit up to 5" propellers and comes in 2 versions. The standard, light-weight version is the 3mm carbon fiber unibody plate, and the 4mm version is for those looking for maximum strength and durability.
Includes

    1x QAV-X CHARPU Carbon Fiber airframe kit (3mm)
        3mm carbon fiber unibody main plate
        2mm carbon fiber top plate
        1.5mm carbon fiber antenna plate
        2x 1.5mm carbon fiber camera sidewall plates
        1x 1.5mm HD camera mounting plate
        1x 1.5mm Battery protector plate
    1x Set of black steel screws and aluminum hardware including knurled spacers
    1x Lumenier 4Power Power distribution board + 3mm spacer / screw set
    1x set 6mm black polyamide spacers / screws for flight controller
    1x XT-60 Pig-Tail
    2x Neoprene foam tape
    1x Lumenier small lipo strap

Lumenier 2350KV Motor:

Lumenier brushless multirotor motors were designed to give you top of the line performance and value for your RC models. This Lumenier RX2206-11 2350Kv motor has been engineered from the ground up, and it is the perfect blend of elegant design and high end performance. By using high quality bearings and CNC precision machined parts, each Lumenier motor provides silky smooth, reliable power.

The Lumenier RX2206-11 2350Kv motors have a strong 3mm internal shaft which has been machine pressed into the upper bell of the motor. No longer is there a need for set screws that loosen over time. The motor features an integrated 5mm threaded prop adapter allowing you to directly mount the propeller to the motor without the need of a separate prop adapter, saving you weight. An ultra-lightweight, black anodized, low profile, flanged aluminum lock nut is also included with each motor ensuring your propellers do not come loose during flight. Each motor comes with 4x M3x5 screws for mounting on most airframes. The motor wire length is 100mm and includes pre-soldered male 2mm bullet connectors for easy installation. Alternatively, you can also simply cut the motor wires to the desired length and directly solder them to your ESC.
Includes

    1x Lumenier RX2206-11 2350Kv Motor
    1x Lumenier M5 Black Aluminum Low Profile Lock Nut (CW)
    4x M3x5 Button head screws

Specifications
Kv     2350
Configuration     12N14P
Windings     11 turn DLRK
Termination     D (Delta)
Stator Diameter     22mm
Shaft Diameter     3mm
Motor Dimension     27x17mm
Weight     26.5g, (29g with bullets)
Idle Current @12.6v (Io)     0.81A
Cells (LiPo)     2-4S
Max Continuous Current (A) 60s     16A
Max Burst Current <10s     32A
Max Continuous Power (W) 60s     260W
Max Efficiency Current     (2.2-6A) 80%
Internal Resistance (Rm)     260mΩ
Motor Wire Length     100mm
Motor Connection     Male 2mm bullet

Spectrum SPMFC3207:

Clean up your next mini quad build with the SPMFC3207. Based on the reliable STM32F3 Racing chipset, this Flight controller Combo incorporates a simple to use PDB that the builder can wire all ESC wires and have easy access to 3 amps of clean, regulated 12v and 5v pads for powering accessories. And with just a single connection from PDB to the FC, repairing your downed aircraft is easy and accessible. 

The Flight controller features BetaFlight 3.1 preinstalled and has updates available on the BetaFlight Configurator. 

The FC3207 flight controller comes ready out of the box to be used with the Spektrum 4649T receiver for Battery voltage and RSSI telemetry feedback. Also there is a easy to access Bind Button, making binding your Spektrum receivers quick and easy. 

Specifications:

 

Input Voltage: 7-18 Volts 
Output Voltage: 5v and 12v Aux Rails 
Pre-Loaded Firmware: Betaflight 
Processor: F303 
Supports: Oneshot and Multishot ESCs 
Requires: Soldering 
Includes: Complete FC Stack = FC w/ PDB and Micro USB Connector for Programming 
Dimensions: 36 x 36mm 
Mounting Holes: 30.5 x 30.5mm 
Weight: 19g 
Includes: Complete FC Stack = FC with PDB and Micro USB Connector for Programming


Our Price: $199.99    Sold By:

Qty Desired:   Add to Cart